--- System Configuration Dialog --- Continue with configuration dialog? [yes/no]: no Router>enable Router#erase startup-config Erasing the nvram filesystem will remove all configuration files! Continue? [confirm] [OK] Erase of nvram: complete %SYS-7-NV_BLOCK_INIT: Initialized the geometry of nvram Router#reload Proceed with reload? [confirm] System Bootstrap, Version 12.3(8r)T8, RELEASE SOFTWARE (fc1) Cisco 1841 (revision 5.0) with 114688K/16384K bytes of memory. Self decompressing the image : ########################################################################## [OK] Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.3(14)T7, RELEASE SOFTWARE (fc2) Technical Support: cisco/techsupport Copyright (c) 1986-2006 by Cisco Systems, Inc. Compiled Mon 15-May-06 14:54 by pt_team Image text-base: 0x6007D180, data-base: 0x61400000 Port Statistics for unclassified packets is not turned on. Cisco 1841 (revision 5.0) with 114688K/16384K bytes of memory. Processor board ID FTX0947Z18E M860 processor: part number 0, mask 49 2 FastEthernet/IEEE 802.3 interface(s) 2 Low-speed serial(sync/async) network interface(s) 191K bytes of NVRAM. 32768K bytes of ATA CompactFlash (Read/Write) Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.3(14)T7, RELEASE SOFTWARE (fc2) Technical Support: cisco/techsupport Copyright (c) 1986-2006 by Cisco Systems, Inc. Compiled Mon 15-May-06 14:54 by pt_team --- System Configuration Dialog --- Continue with configuration dialog? [yes/no]: yes At any point you may enter a question mark ? for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets []. Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system Would you like to enter basic management setup? [yes/no]: yes Configuring global parameters: Enter host name [Router]: R2 The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration. Enter enable secret: class The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images. Enter enable password: cisco The virtual terminal password is used to protect access to the router over a network interface. Enter virtual terminal password: cisco Configure SNMP Network Management? [no]: Current interface summary Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES manual administratively down down FastEthernet0/1 unassigned YES manual administratively down down Serial0/0/0 unassigned YES manual administratively down down Serial0/0/1 unassigned YES manual administratively down down Vlan1 unassigned YES manual administratively down down Enter interface name used to connect to the management network from the above interface summary: fastethernet0/0 Configuring interface FastEthernet0/0: Configure IP on this interface? [yes]: yes IP address for this interface: 192.168.2.2 Subnet mask for this interface [255.255.255.0] : The following configuration command script was created: ! hostname R2 enable secret 5 $1$mERr$9cTjUIEqNGurQiFU.ZeCi1 enable password cisco line vty 0 4 password cisco ! interface Vlan1 shutdown no ip address ! interface FastEthernet0/0 no shutdown ip address 192.168.2.2 255.255.255.0 ! interface FastEthernet0/1 shutdown no ip address ! interface Serial0/0/0 shutdown no ip address ! interface Serial0/0/1 shutdown no ip address ! end [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. Enter your selection [2]: Building configuration... [OK] Use the enabled mode configure command to modify this configuration. Press RETURN to get started! %LINK-5-CHANGED: Interface Vlan1, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up %LINK-5-CHANGED: Interface Serial0/0/1, changed state to up %LINK-5-CHANGED: Interface Vlan1, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down %LINK-5-CHANGED: Interface Serial0/0/1, changed state to administratively down %SYS-5-CONFIG_I: Configured from console by console R2> R2>enable Password: R2#show running-config Building configuration... Current configuration : 683 bytes ! version 12.3 no service timestamps log datetime msec no service timestamps debug datetime msec no service password-encryption ! hostname R2 ! ! ! enable secret 5 $1$mERr$9cTjUIEqNGurQiFU.ZeCi1 enable password cisco ! ! ! ! ! ! ! R2#
Posted on: Tue, 15 Oct 2013 03:32:05 +0000
Trending Topics
Recently Viewed Topics
© 2015